Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H715300

Cone Part Number

 N/A H715341

Cup Part Number

 N/A H715310

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.6250 in66.675 mm

D - Cup Outer Diameter

 N/A 5.5000 in139.700 mm

B - Cone Width

 N/A 1.8125 in46.038 mm

C - Cup Width

 N/A 1.4375 in36.513 mm

T - Bearing Width

 N/A 1.8125 in46.038 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.35 in85 mm

db - Cone Backface Backing Diameter

 N/A 3.58 in91 mm

Da - Cup Frontface Backing Diameter

 N/A 5.25 in133.35 mm

Db - Cup Backface Backing Diameter

 N/A 4.72 in119.89 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.14 in3.6 mm
a - Effective Center Location3 N/A -0.34 in-8.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 18600 lbf82700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 71700 lbf319000 N

C0 - Static Radial Rating

 N/A 91000 lbf405000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 15100 lbf67000 N

Factors

K - Factor7 N/A 1.24
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 147

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 32.8
Cg - Geometry Factor10 N/A 0.0993
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.