Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H816200

Cone Part Number

 N/A H816249

Cup Part Number

 N/A H816210

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3.0625 in77.788 mm

D - Cup Outer Diameter

 N/A 6.4951 in164.976 mm

B - Cone Width

 N/A 1.8208 in46.248 mm

C - Cup Width

 N/A 1.4272 in36.251 mm

T - Bearing Width

 N/A 1.9488 in49.5 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.64 in92.5 mm

db - Cone Backface Backing Diameter

 N/A 4.02 in102 mm

Da - Cup Frontface Backing Diameter

 N/A 6.09 in154.70 mm

Db - Cup Backface Backing Diameter

 N/A 5.67 in144.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.27 in6.9 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.15 in3.8 mm
a - Effective Center Location3 N/A -0.25 in-6.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 20500 lbf91100 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 79000 lbf352000 N

C0 - Static Radial Rating

 N/A 90000 lbf400000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 17900 lbf79700 N

Factors

K - Factor7 N/A 1.14
e - ISO Factor8 N/A 0.51
Y - ISO Factor9 N/A 1.17

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 127

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 23.2
Cg - Geometry Factor10 N/A 0.0959
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.