Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H924000

Cone Part Number

 N/A H924033

Cup Part Number

 N/A H924010

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4 in101.600 mm

D - Cup Outer Diameter

 N/A 8.4375 in214.313 mm

B - Cone Width

 N/A 2.0625 in52.388 mm

C - Cup Width

 N/A 1.5625 in39.688 mm

T - Bearing Width

 N/A 2.1875 in55.563 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 5.04 in128 mm

db - Cone Backface Backing Diameter

 N/A 5.2 in132 mm

Da - Cup Frontface Backing Diameter

 N/A 8.11 in205.00 mm

Db - Cup Backface Backing Diameter

 N/A 7.32 in185.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.23 in5.8 mm
a - Effective Center Location3 N/A 0.27 in6.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 32500 lbf144000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 125000 lbf557000 N

C0 - Static Radial Rating

 N/A 137000 lbf610000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 37500 lbf167000 N

Factors

K - Factor7 N/A 0.87
e - ISO Factor8 N/A 0.67
Y - ISO Factor9 N/A 0.89

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 246

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 32.2
Cg - Geometry Factor10 N/A 0.13
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.