Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH258200

Cone Part Number

 N/A HH258248

Cup Part Number

 N/A HH258210

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 11.8100 in299.974 mm

D - Cup Outer Diameter

 N/A 19.5000 in495.300 mm

B - Cone Width

 N/A 5.5625 in141.288 mm

C - Cup Width

 N/A 4.5000 in114.300 mm

T - Bearing Width

 N/A 5.5625 in141.288 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 13.07 in332 mm

db - Cone Backface Backing Diameter

 N/A 13.46 in342 mm

Da - Cup Frontface Backing Diameter

 N/A 18.43 in467.40 mm

Db - Cup Backface Backing Diameter

 N/A 17.64 in448.06 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.36 in9.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.36 in9.1 mm
a - Effective Center Location3 N/A -1.36 in-34.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 167000 lbf744000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 645000 lbf2870000 N

C0 - Static Radial Rating

 N/A 1270000 lbf5650000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 95200 lbf423000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3850

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 220
Cg - Geometry Factor10 N/A 0.205
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.