Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH923600

Cone Part Number

 N/A HH923649

Cup Part Number

 N/A HH923610

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4 in101.600 mm

D - Cup Outer Diameter

 N/A 9.8750 in250.825 mm

B - Cone Width

 N/A 2.875 in73.025 mm

C - Cup Width

 N/A 2.0000 in50.800 mm

T - Bearing Width

 N/A 3.0000 in76.200 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 5.15 in130.8 mm

db - Cone Backface Backing Diameter

 N/A 5.87 in149 mm

Da - Cup Frontface Backing Diameter

 N/A 9.02 in229.10 mm

Db - Cup Backface Backing Diameter

 N/A 8.15 in207.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.23 in5.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.55 in14 mm
a - Effective Center Location3 N/A -0.13 in-3.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 48200 lbf215000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 186000 lbf828000 N

C0 - Static Radial Rating

 N/A 186000 lbf827000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 57800 lbf257000 N

Factors

K - Factor7 N/A 0.84
e - ISO Factor8 N/A 0.7
Y - ISO Factor9 N/A 0.86

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 282

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 35.2
Cg - Geometry Factor10 N/A 0.137
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.