Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH926700

Cone Part Number

 N/A HH926749A

Cup Part Number

 N/A HH926710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4.7500 in120.650 mm

D - Cup Outer Diameter

 N/A 10.7500 in273.050 mm

B - Cone Width

 N/A 3.2500 in82.550 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 3.2500 in82.550 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 5.79 in147 mm

db - Cone Backface Backing Diameter

 N/A 6.93 in176 mm

Da - Cup Frontface Backing Diameter

 N/A 10.00 in254.00 mm

Db - Cup Backface Backing Diameter

 N/A 9.06 in230.12 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.2 in5.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.56 in14.2 mm
a - Effective Center Location3 N/A -0.26 in-6.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 52400 lbf233000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 202000 lbf899000 N

C0 - Static Radial Rating

 N/A 243000 lbf1080000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 56700 lbf252000 N

Factors

K - Factor7 N/A 0.92
e - ISO Factor8 N/A 0.63
Y - ISO Factor9 N/A 0.95

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 384.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 37.8
Cg - Geometry Factor10 N/A 0.147
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.