Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH949500

Cone Part Number

 N/A HH949549

Cup Part Number

 N/A HH949510

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 9 in228.600 mm

D - Cup Outer Diameter

 N/A 19.2500 in488.950 mm

B - Cone Width

 N/A 4.3750 in111.125 mm

C - Cup Width

 N/A 2.875 in73.025 mm

T - Bearing Width

 N/A 4.8750 in123.825 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 11.02 in280 mm

db - Cone Backface Backing Diameter

 N/A 11.69 in297 mm

Da - Cup Frontface Backing Diameter

 N/A 17.96 in456.18 mm

Db - Cup Backface Backing Diameter

 N/A 16.38 in416.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.58 in14.7 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.9 in22.9 mm
a - Effective Center Location3 N/A 1.57 in39.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 131000 lbf582000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 505000 lbf2240000 N

C0 - Static Radial Rating

 N/A 564000 lbf2510000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 210000 lbf934000 N

Factors

K - Factor7 N/A 0.62
e - ISO Factor8 N/A 0.94
Y - ISO Factor9 N/A 0.64

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1300

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 91.5
Cg - Geometry Factor10 N/A 0.193
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.