Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH953700

Cone Part Number

 N/A HH953749

Cup Part Number

 N/A HH953710

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A HH953749-90026 HH953749-90046

Dimensions

d - Bore

 N/A 10 in254 mm

D - Cup Outer Diameter

 N/A 21.0 in533.400 mm

B - Cone Width

 N/A 4.7500 in120.650 mm

C - Cup Width

 N/A 3.0625 in77.788 mm

T - Bearing Width

 N/A 5.2500 in133.350 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 12.05 in306 mm

db - Cone Backface Backing Diameter

 N/A 13.78 in350 mm

Da - Cup Frontface Backing Diameter

 N/A 19.54 in495.60 mm

Db - Cup Backface Backing Diameter

 N/A 17.91 in454.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.71 in18 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.86 in21.8 mm
a - Effective Center Location3 N/A 1.79 in45.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 156000 lbf696000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 603000 lbf2680000 N

C0 - Static Radial Rating

 N/A 694000 lbf3090000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 251000 lbf1120000 N

Factors

K - Factor7 N/A 0.62
e - ISO Factor8 N/A 0.94
Y - ISO Factor9 N/A 0.64

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1668.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 104.2
Cg - Geometry Factor10 N/A 0.210
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.