Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM161000

Cone Part Number

 N/A HM161040

Cup Part Number

 N/A HM161012

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 12.2000 in309.880 mm

D - Cup Outer Diameter

 N/A 19.7500 in501.650 mm

B - Cone Width

 N/A 3.8750 in98.425 mm

C - Cup Width

 N/A 3.1250 in79.375 mm

T - Bearing Width

 N/A 3.8750 in98.425 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 13.35 in339 mm

db - Cone Backface Backing Diameter

 N/A 13.7 in348 mm

Da - Cup Frontface Backing Diameter

 N/A 18.72 in475.49 mm

Db - Cup Backface Backing Diameter

 N/A 18.43 in468.12 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.32 in8.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.07 in1.8 mm
a - Effective Center Location3 N/A -0.47 in-11.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 152000 lbf675000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 585000 lbf2600000 N

C0 - Static Radial Rating

 N/A 848000 lbf3770000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 77900 lbf346000 N

Factors

K - Factor7 N/A 1.95
e - ISO Factor8 N/A 0.3
Y - ISO Factor9 N/A 2

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3153.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 239.4
Cg - Geometry Factor10 N/A 0.184
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.