Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM215200

Cone Part Number

 N/A HM215249

Cup Part Number

 N/A HM215210

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.9916 in75.987 mm

D - Cup Outer Diameter

 N/A 5.1959 in131.976 mm

B - Cone Width

 N/A 1.5354 in38.999 mm

C - Cup Width

 N/A 1.2598 in31.999 mm

T - Bearing Width

 N/A 1.5354 in38.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.110 mm
r - Cup Backface "To Clear" Radius2 N/A 0.140 in3.56 mm

da - Cone Frontface Backing Diameter

 N/A 3.35 in85 mm

db - Cone Backface Backing Diameter

 N/A 3.86 in98 mm

Da - Cup Frontface Backing Diameter

 N/A 5.00 in126.00 mm

Db - Cup Backface Backing Diameter

 N/A 4.65 in118.11 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.14 in3.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.03 in0.8 mm
a - Effective Center Location3 N/A -0.38 in-9.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 14000 lbf62200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 53900 lbf240000 N

C0 - Static Radial Rating

 N/A 72800 lbf324000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 7960 lbf35400 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 126

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 30.2
Cg - Geometry Factor10 N/A 0.0837
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.