Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM218200

Cone Part Number

 N/A HM218248

Cup Part Number

 N/A HM218210

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3.5423 in89.974 mm

D - Cup Outer Diameter

 N/A 5.7864 in146.975 mm

B - Cone Width

 N/A 1.5748 in40.000 mm

C - Cup Width

 N/A 1.2795 in32.499 mm

T - Bearing Width

 N/A 1.5748 in40.000 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.110 mm
r - Cup Backface "To Clear" Radius2 N/A 0.140 in3.56 mm

da - Cone Frontface Backing Diameter

 N/A 3.9 in99 mm

db - Cone Backface Backing Diameter

 N/A 4.41 in112 mm

Da - Cup Frontface Backing Diameter

 N/A 5.57 in141.00 mm

Db - Cup Backface Backing Diameter

 N/A 5.24 in133.10 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.14 in3.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.04 in1 mm
a - Effective Center Location3 N/A -0.34 in-8.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 18900 lbf84200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 73000 lbf325000 N

C0 - Static Radial Rating

 N/A 87300 lbf388000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 10800 lbf47900 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 168.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 34.7
Cg - Geometry Factor10 N/A 0.0921
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.