Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM220100

Cone Part Number

 N/A HM220149

Cup Part Number

 N/A HM220110

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3.9360 in99.974 mm

D - Cup Outer Diameter

 N/A 6.1801 in156.975 mm

B - Cone Width

 N/A 1.6535 in41.999 mm

C - Cup Width

 N/A 1.3386 in34 mm

T - Bearing Width

 N/A 1.6535 in41.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.870 mm
r - Cup Backface "To Clear" Radius2 N/A 0.140 in3.56 mm

da - Cone Frontface Backing Diameter

 N/A 4.25 in108 mm

db - Cone Backface Backing Diameter

 N/A 4.84 in122.9 mm

Da - Cup Frontface Backing Diameter

 N/A 5.96 in151.38 mm

Db - Cup Backface Backing Diameter

 N/A 5.59 in141.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.07 in1.8 mm
a - Effective Center Location3 N/A -0.34 in-8.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 17500 lbf77800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 67500 lbf300000 N

C0 - Static Radial Rating

 N/A 98500 lbf438000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 9960 lbf44300 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 203.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 45.9
Cg - Geometry Factor10 N/A 0.0981
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.