Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM237500

Cone Part Number

 N/A HM237532

Cup Part Number

 N/A HM237510

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 6.3120 in160.325 mm

D - Cup Outer Diameter

 N/A 11.3750 in288.925 mm

B - Cone Width

 N/A 2.5 in63.5 mm

C - Cup Width

 N/A 1.8750 in47.625 mm

T - Bearing Width

 N/A 2.5000 in63.500 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.100 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 7.13 in181 mm

db - Cone Backface Backing Diameter

 N/A 7.56 in192 mm

Da - Cup Frontface Backing Diameter

 N/A 10.69 in271.30 mm

Db - Cup Backface Backing Diameter

 N/A 10.47 in265.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.2 in5.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.2 in5.1 mm
a - Effective Center Location3 N/A -0.46 in-11.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 56900 lbf253000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 219000 lbf976000 N

C0 - Static Radial Rating

 N/A 278000 lbf1240000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 31100 lbf138000 N

Factors

K - Factor7 N/A 1.83
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.88

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 751.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 101.5
Cg - Geometry Factor10 N/A 0.117
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.