Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM237500

Cone Part Number

 N/A HM237537

Cup Part Number

 N/A HM237513

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 6.4951 in164.976 mm

D - Cup Outer Diameter

 N/A 11.4163 in289.974 mm

B - Cone Width

 N/A 2.6772 in68.001 mm

C - Cup Width

 N/A 1.8898 in48.001 mm

T - Bearing Width

 N/A 2.5001 in63.503 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.100 mm
r - Cup Backface "To Clear" Radius2 N/A 0.12 in3.05 mm

da - Cone Frontface Backing Diameter

 N/A 7.24 in184 mm

db - Cone Backface Backing Diameter

 N/A 7.68 in195 mm

Da - Cup Frontface Backing Diameter

 N/A 10.71 in272.00 mm

Db - Cup Backface Backing Diameter

 N/A 10.51 in266.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.13 in3.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.18 in4.6 mm
a - Effective Center Location3 N/A -0.46 in-11.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 48800 lbf217000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 188000 lbf837000 N

C0 - Static Radial Rating

 N/A 254000 lbf1130000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 26600 lbf119000 N

Factors

K - Factor7 N/A 1.83
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.88

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 704.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 95.5
Cg - Geometry Factor10 N/A 0.114
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.