Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM259000

Cone Part Number

 N/A HM259049

Cup Part Number

 N/A HM259010

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A HM259049-90401

Dimensions

d - Bore

 N/A 12.5000 in317.500 mm

D - Cup Outer Diameter

 N/A 17.6250 in447.675 mm

B - Cone Width

 N/A 3.3750 in85.725 mm

C - Cup Width

 N/A 2.6875 in68.263 mm

T - Bearing Width

 N/A 3.3750 in85.725 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 13.27 in337 mm

db - Cone Backface Backing Diameter

 N/A 13.43 in341 mm

Da - Cup Frontface Backing Diameter

 N/A 16.85 in427.99 mm

Db - Cup Backface Backing Diameter

 N/A 16.46 in418.08 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.21 in5.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.19 in4.8 mm
a - Effective Center Location3 N/A -0.19 in-4.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 97800 lbf435000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 377000 lbf1680000 N

C0 - Static Radial Rating

 N/A 706000 lbf3140000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 56000 lbf249000 N

Factors

K - Factor7 N/A 1.74
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.79

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2944.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 303.9
Cg - Geometry Factor10 N/A 0.186
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.