Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM807000

Cone Part Number

 N/A HM807035

Cup Part Number

 N/A HM807011

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 5/8 in41.275 mm

D - Cup Outer Diameter

 N/A 4.1250 in104.775 mm

B - Cone Width

 N/A 1.4375 in36.513 mm

C - Cup Width

 N/A 1.1250 in28.575 mm

T - Bearing Width

 N/A 1.4375 in36.513 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 2.24 in57 mm

db - Cone Backface Backing Diameter

 N/A 2.36 in60 mm

Da - Cup Frontface Backing Diameter

 N/A 3.96 in100.10 mm

Db - Cup Backface Backing Diameter

 N/A 3.58 in90.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.1 in2.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.12 in3 mm
a - Effective Center Location3 N/A -0.29 in-7.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 10000 lbf44500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 38600 lbf172000 N

C0 - Static Radial Rating

 N/A 50200 lbf223000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8350 lbf37100 N

Factors

K - Factor7 N/A 1.2
e - ISO Factor8 N/A 0.49
Y - ISO Factor9 N/A 1.23
Cg - Geometry Factor10 N/A 0.0760
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.