Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L281100

Cone Part Number

 N/A L281146

Cup Part Number

 N/A L281110

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A L281146-90024

Dimensions

d - Bore

 N/A 25.9935 in660.235 mm

D - Cup Outer Diameter

 N/A 32.0000 in812.800 mm

B - Cone Width

 N/A 3.7500 in95.250 mm

C - Cup Width

 N/A 2.875 in73.025 mm

T - Bearing Width

 N/A 3.7500 in95.250 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 26.81 in681 mm

db - Cone Backface Backing Diameter

 N/A 27.28 in693 mm

Da - Cup Frontface Backing Diameter

 N/A 31.32 in795.53 mm

Db - Cup Backface Backing Diameter

 N/A 30.59 in776.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.27 in6.9 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.29 in7.4 mm
a - Effective Center Location3 N/A 1.1 in27.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 148000 lbf657000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 570000 lbf2530000 N

C0 - Static Radial Rating

 N/A 1340000 lbf5940000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 84100 lbf374000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 11700

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 915
Cg - Geometry Factor10 N/A 0.289
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.