Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L467500

Cone Part Number

 N/A L467549

Cup Part Number

 N/A L467510

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A L467549-902A2 L467549-903A3

Dimensions

d - Bore

 N/A 16.0000 in406.400 mm

D - Cup Outer Diameter

 N/A 20.0000 in508.000 mm

B - Cone Width

 N/A 2.4375 in61.913 mm

C - Cup Width

 N/A 1.8750 in47.625 mm

T - Bearing Width

 N/A 2.4375 in61.913 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 16.65 in423 mm

db - Cone Backface Backing Diameter

 N/A 16.77 in426 mm

Da - Cup Frontface Backing Diameter

 N/A 19.49 in495.00 mm

Db - Cup Backface Backing Diameter

 N/A 19.02 in483.11 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.2 in5.1 mm
a - Effective Center Location3 N/A 0.8 in20.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 50100 lbf223000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 193000 lbf859000 N

C0 - Static Radial Rating

 N/A 502000 lbf2230000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 31300 lbf139000 N

Factors

K - Factor7 N/A 1.6
e - ISO Factor8 N/A 0.37
Y - ISO Factor9 N/A 1.64

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3720

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 673
Cg - Geometry Factor10 N/A 0.204
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.