Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L507900

Cone Part Number

 N/A L507949

Cup Part Number

 N/A L507910

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A L507949-90012 L507949-90404

Dimensions

d - Bore

 N/A 2 1/4 in57.15 mm

D - Cup Outer Diameter

 N/A 3.4375 in87.313 mm

B - Cone Width

 N/A 0.7188 in18.258 mm

C - Cup Width

 N/A 0.5625 in14.288 mm

T - Bearing Width

 N/A 0.7188 in18.258 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 2.44 in62 mm

db - Cone Backface Backing Diameter

 N/A 2.56 in65 mm

Da - Cup Frontface Backing Diameter

 N/A 3.29 in83.10 mm

Db - Cup Backface Backing Diameter

 N/A 3.11 in78.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.1 in2.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A -0.03 in-0.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3650 lbf16300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 14100 lbf62700 N

C0 - Static Radial Rating

 N/A 21500 lbf95600 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2430 lbf10800 N

Factors

K - Factor7 N/A 1.5
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.54

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 46.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 38.5
Cg - Geometry Factor10 N/A 0.0914
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.