Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L730600

Cone Part Number

 N/A L730649

Cup Part Number

 N/A L730610

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A L730649-905A1

Dimensions

d - Bore

 N/A 6 in152.400 mm

D - Cup Outer Diameter

 N/A 8 in203.2 mm

B - Cone Width

 N/A 1.1250 in28.575 mm

C - Cup Width

 N/A 0.8440 in21.438 mm

T - Bearing Width

 N/A 1.1250 in28.575 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 6.3 in160 mm

db - Cone Backface Backing Diameter

 N/A 6.5 in165 mm

Da - Cup Frontface Backing Diameter

 N/A 7.83 in198.88 mm

Db - Cup Backface Backing Diameter

 N/A 7.48 in189.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.08 in2 mm
a - Effective Center Location3 N/A 0.45 in11.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 11300 lbf50200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 43500 lbf194000 N

C0 - Static Radial Rating

 N/A 76100 lbf339000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8860 lbf39400 N

Factors

K - Factor7 N/A 1.27
e - ISO Factor8 N/A 0.46
Y - ISO Factor9 N/A 1.31

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 295

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 103
Cg - Geometry Factor10 N/A 0.176
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.