Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L778100

Cone Part Number

 N/A L778149

Cup Part Number

 N/A L778110

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A L778149-90010 L778149-90017

Dimensions

d - Bore

 N/A 23.0000 in584.200 mm

D - Cup Outer Diameter

 N/A 27.9375 in709.613 mm

B - Cone Width

 N/A 2.2500 in57.150 mm

C - Cup Width

 N/A 1.5625 in39.688 mm

T - Bearing Width

 N/A 2.3125 in58.738 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 23.74 in603 mm

db - Cone Backface Backing Diameter

 N/A 23.86 in606 mm

Da - Cup Frontface Backing Diameter

 N/A 27.28 in692.91 mm

Db - Cup Backface Backing Diameter

 N/A 26.93 in684.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.31 in7.87 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.14 in3.56 mm
a - Effective Center Location3 N/A 2.71 in68.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 70300 lbf313000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 271000 lbf1210000 N

C0 - Static Radial Rating

 N/A 659000 lbf2930000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 57200 lbf254000 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.26

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5712.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1057.7
Cg - Geometry Factor10 N/A 0.254
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.