Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L853000

Cone Part Number

 N/A L853048

Cup Part Number

 N/A L853010W

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 10.8268 in275.001 mm

D - Cup Outer Diameter

 N/A 13.875 in352.425 mm

B - Cone Width

 N/A 1.5748 in40.000 mm

C - Cup Width

 N/A 0.9375 in23.813 mm

T - Bearing Width

 N/A 1.4375 in36.513 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 11.3 in287 mm

db - Cone Backface Backing Diameter

 N/A 11.5 in292 mm

Da - Cup Frontface Backing Diameter

 N/A 13.50 in341.90 mm

Db - Cup Backface Backing Diameter

 N/A 13.07 in331.98 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.05 in1.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.14 in3.6 mm
a - Effective Center Location3 N/A 1.38 in35.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 17800 lbf79200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 68700 lbf306000 N

C0 - Static Radial Rating

 N/A 149000 lbf664000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 16400 lbf73100 N

Factors

K - Factor7 N/A 1.08
e - ISO Factor8 N/A 0.54
Y - ISO Factor9 N/A 1.11
Cg - Geometry Factor10 N/A 0.147
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.