Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L879900

Cone Part Number

 N/A L879946

Cup Part Number

 N/A L879910

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A L879946-90018

Dimensions

d - Bore

 N/A 23.9920 in609.397 mm

D - Cup Outer Diameter

 N/A 30.0000 in762.000 mm

B - Cone Width

 N/A 3.6250 in92.075 mm

C - Cup Width

 N/A 2.8125 in71.438 mm

T - Bearing Width

 N/A 3.7500 in95.250 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 24.92 in633 mm

db - Cone Backface Backing Diameter

 N/A 25.28 in642 mm

Da - Cup Frontface Backing Diameter

 N/A 29.27 in743.46 mm

Db - Cup Backface Backing Diameter

 N/A 28.35 in720.09 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.29 in7.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.39 in9.9 mm
a - Effective Center Location3 N/A 2.28 in57.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 115000 lbf513000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 445000 lbf1980000 N

C0 - Static Radial Rating

 N/A 1230000 lbf5470000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 96300 lbf428000 N

Factors

K - Factor7 N/A 1.2
e - ISO Factor8 N/A 0.49
Y - ISO Factor9 N/A 1.23

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 9580

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1010
Cg - Geometry Factor10 N/A 0.306
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.