Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL217800

Cone Part Number

 N/A LL217849

Cup Part Number

 N/A LL217810

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LL217849-90010 LL217849-902A5

Dimensions

d - Bore

 N/A 3 1/2 in88.900 mm

D - Cup Outer Diameter

 N/A 4.7812 in121.442 mm

B - Cone Width

 N/A 0.5938 in15.083 mm

C - Cup Width

 N/A 0.4375 in11.113 mm

T - Bearing Width

 N/A 0.5938 in15.083 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 3.7 in94 mm

db - Cone Backface Backing Diameter

 N/A 3.82 in97 mm

Da - Cup Frontface Backing Diameter

 N/A 4.65 in117.10 mm

Db - Cup Backface Backing Diameter

 N/A 4.53 in115.06 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A 0.12 in3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3470 lbf15400 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 13400 lbf59500 N

C0 - Static Radial Rating

 N/A 20000 lbf88700 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1960 lbf8730 N

Factors

K - Factor7 N/A 1.77
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.81

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 73.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 74.1
Cg - Geometry Factor10 N/A 0.0996
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.