Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL562700

Cone Part Number

 N/A LL562749

Cup Part Number

 N/A LL562710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 14.2500 in361.950 mm

D - Cup Outer Diameter

 N/A 16.0000 in406.400 mm

B - Cone Width

 N/A 0.9375 in23.813 mm

C - Cup Width

 N/A 0.6875 in17.463 mm

T - Bearing Width

 N/A 0.9375 in23.813 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.290 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 14.61 in371 mm

db - Cone Backface Backing Diameter

 N/A 14.65 in372 mm

Da - Cup Frontface Backing Diameter

 N/A 15.83 in402.08 mm

Db - Cup Backface Backing Diameter

 N/A 15.59 in395.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.14 in3.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.01 in0.3 mm
a - Effective Center Location3 N/A 1.49 in37.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 11500 lbf51300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 44500 lbf198000 N

C0 - Static Radial Rating

 N/A 129000 lbf574000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 7940 lbf35300 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1670

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1060
Cg - Geometry Factor10 N/A 0.201
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.