Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL641100

Cone Part Number

 N/A LL641149

Cup Part Number

 N/A LL641111

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 8 in203.2 mm

D - Cup Outer Diameter

 N/A 10.2812 in261.142 mm

B - Cone Width

 N/A 1.0938 in27.783 mm

C - Cup Width

 N/A 0.8438 in21.433 mm

T - Bearing Width

 N/A 1.1250 in28.575 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 8.35 in212 mm

db - Cone Backface Backing Diameter

 N/A 8.43 in214 mm

Da - Cup Frontface Backing Diameter

 N/A 10.02 in254.51 mm

Db - Cup Backface Backing Diameter

 N/A 9.80 in248.92 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.1 in2.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.1 in2.5 mm
a - Effective Center Location3 N/A 0.62 in15.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 12100 lbf53900 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 46700 lbf208000 N

C0 - Static Radial Rating

 N/A 91100 lbf405000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8480 lbf37700 N

Factors

K - Factor7 N/A 1.43
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.47

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 521.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 231.1
Cg - Geometry Factor10 N/A 0.14
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.