Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL771900

Cone Part Number

 N/A LL771948

Cup Part Number

 N/A LL771911

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LL771948-90010 LL771948-903A5

Dimensions

d - Bore

 N/A 18.7500 in476.250 mm

D - Cup Outer Diameter

 N/A 22.2500 in565.150 mm

B - Cone Width

 N/A 1.625 in41.275 mm

C - Cup Width

 N/A 1.2500 in31.750 mm

T - Bearing Width

 N/A 1.6250 in41.275 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 19.33 in491 mm

db - Cone Backface Backing Diameter

 N/A 19.49 in495 mm

Da - Cup Frontface Backing Diameter

 N/A 21.66 in548.90 mm

Db - Cup Backface Backing Diameter

 N/A 21.38 in543.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.1 in2.5 mm
a - Effective Center Location3 N/A 2.3 in58.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 27400 lbf122000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 106000 lbf469000 N

C0 - Static Radial Rating

 N/A 315000 lbf1400000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 22000 lbf97800 N

Factors

K - Factor7 N/A 1.24
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.28

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3790

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1240
Cg - Geometry Factor10 N/A 0.219
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.