Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL788300

Cone Part Number

 N/A LL788345

Cup Part Number

 N/A LL788310

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 41.8750 in1063.625 mm

D - Cup Outer Diameter

 N/A 48.0000 in1219.200 mm

B - Cone Width

 N/A 2.5625 in65.088 mm

C - Cup Width

 N/A 1.6875 in42.863 mm

T - Bearing Width

 N/A 2.5625 in65.088 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 42.72 in1085 mm

db - Cone Backface Backing Diameter

 N/A 42.91 in1090 mm

Da - Cup Frontface Backing Diameter

 N/A 47.24 in1199.90 mm

Db - Cup Backface Backing Diameter

 N/A 46.65 in1184.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.48 in12.19 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.11 in2.79 mm
a - Effective Center Location3 N/A 5.61 in142.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 100000 lbf445000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 386000 lbf1720000 N

C0 - Static Radial Rating

 N/A 1270000 lbf5660000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 81400 lbf362000 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.26
Cg - Geometry Factor10 N/A 0.392
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.