Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LL789700

Cone Part Number

 N/A LL789749

Cup Part Number

 N/A LL789710

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 66.5000 in1689.100 mm

D - Cup Outer Diameter

 N/A 72.6250 in1844.675 mm

B - Cone Width

 N/A 2.6875 in68.263 mm

C - Cup Width

 N/A 1.6875 in42.863 mm

T - Bearing Width

 N/A 2.6875 in68.263 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 67.32 in1710 mm

db - Cone Backface Backing Diameter

 N/A 67.72 in1720 mm

Da - Cup Frontface Backing Diameter

 N/A 77.40 in1966.00 mm

Db - Cup Backface Backing Diameter

 N/A 71.06 in1804.92 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.71 in18 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.34 in-8.6 mm
a - Effective Center Location3 N/A 9.62 in244.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 123000 lbf545000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 473000 lbf2100000 N

C0 - Static Radial Rating

 N/A 1990000 lbf8860000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 102000 lbf452000 N

Factors

K - Factor7 N/A 1.21
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.24

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 60700

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 13953.2
Cg - Geometry Factor10 N/A 0.544
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.