Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM119300

Cone Part Number

 N/A LM119348

Cup Part Number

 N/A LM119311

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3 3/4 in95.250 mm

D - Cup Outer Diameter

 N/A 5.3750 in136.525 mm

B - Cone Width

 N/A 1.1875 in30.163 mm

C - Cup Width

 N/A 0.9688 in24.608 mm

T - Bearing Width

 N/A 1.1875 in30.163 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.090 in2.29 mm

da - Cone Frontface Backing Diameter

 N/A 4.02 in102 mm

db - Cone Backface Backing Diameter

 N/A 4.13 in105 mm

Da - Cup Frontface Backing Diameter

 N/A 5.19 in131.10 mm

Db - Cup Backface Backing Diameter

 N/A 4.96 in125.98 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.03 in0.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.04 in1 mm
a - Effective Center Location3 N/A -0.18 in-4.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 8140 lbf36200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 31400 lbf140000 N

C0 - Static Radial Rating

 N/A 51100 lbf227000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3950 lbf17600 N

Factors

K - Factor7 N/A 2.06
e - ISO Factor8 N/A 0.28
Y - ISO Factor9 N/A 2.11

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 149

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 69
Cg - Geometry Factor10 N/A 0.121
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.