Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM229100

Cone Part Number

 N/A LM229140C

Cup Part Number

 N/A LM229110

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 5.3750 in136.525 mm

D - Cup Outer Diameter

 N/A 7.6762 in194.975 mm

B - Cone Width

 N/A 1.2992 in33.000 mm

C - Cup Width

 N/A 1.0827 in27.501 mm

T - Bearing Width

 N/A 1.2993 in33.002 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.140 in3.56 mm

da - Cone Frontface Backing Diameter

 N/A 5.75 in146 mm

db - Cone Backface Backing Diameter

 N/A 5.98 in152 mm

Da - Cup Frontface Backing Diameter

 N/A 7.50 in190.00 mm

Db - Cup Backface Backing Diameter

 N/A 7.17 in182.12 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.13 in3.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.02 in0.5 mm
a - Effective Center Location3 N/A 0.04 in1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 14900 lbf66200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 57400 lbf255000 N

C0 - Static Radial Rating

 N/A 103000 lbf459000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8470 lbf37700 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 365

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 111.1
Cg - Geometry Factor10 N/A 0.171
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.