Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM236700

Cone Part Number

 N/A LM236749

Cup Part Number

 N/A LM236710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM236749-90012

Dimensions

d - Bore

 N/A 7.2500 in184.150 mm

D - Cup Outer Diameter

 N/A 9.25 in234.95 mm

B - Cone Width

 N/A 1.2992 in33.000 mm

C - Cup Width

 N/A 1.1024 in28.001 mm

T - Bearing Width

 N/A 1.3386 in34.000 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.08 in2.030 mm
r - Cup Backface "To Clear" Radius2 N/A 0.08 in2.03 mm

da - Cone Frontface Backing Diameter

 N/A 7.52 in191 mm

db - Cone Backface Backing Diameter

 N/A 7.68 in195 mm

Da - Cup Frontface Backing Diameter

 N/A 9.06 in230.10 mm

Db - Cup Backface Backing Diameter

 N/A 8.82 in224.03 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A 0.2 in5.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 16500 lbf73600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 63800 lbf284000 N

C0 - Static Radial Rating

 N/A 124000 lbf550000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 9480 lbf42200 N

Factors

K - Factor7 N/A 1.74
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.79

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 559

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 173
Cg - Geometry Factor10 N/A 0.135
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.