Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM281000

Cone Part Number

 N/A LM281049

Cup Part Number

 N/A LM281010

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A LM281049-904C4

Dimensions

d - Bore

 N/A 25.4375 in646.113 mm

D - Cup Outer Diameter

 N/A 33.7500 in857.250 mm

B - Cone Width

 N/A 5.5625 in141.288 mm

C - Cup Width

 N/A 4.3125 in109.538 mm

T - Bearing Width

 N/A 5.5625 in141.288 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 26.69 in678 mm

db - Cone Backface Backing Diameter

 N/A 26.93 in684 mm

Da - Cup Frontface Backing Diameter

 N/A 32.48 in824.50 mm

Db - Cup Backface Backing Diameter

 N/A 31.89 in810.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.36 in9.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.44 in11.2 mm
a - Effective Center Location3 N/A 0.12 in3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 274000 lbf1220000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1060000 lbf4700000 N

C0 - Static Radial Rating

 N/A 2330000 lbf10400000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 156000 lbf694000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 14763

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 920.6
Cg - Geometry Factor10 N/A 0.315
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.