Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM377400

Cone Part Number

 N/A LM377449

Cup Part Number

 N/A LM377410

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A LM377449-90041 LM377449-90047

Dimensions

d - Bore

 N/A 22 in558.8 mm

D - Cup Outer Diameter

 N/A 29.0000 in736.600 mm

B - Cone Width

 N/A 4.1250 in104.775 mm

C - Cup Width

 N/A 3.1875 in80.963 mm

T - Bearing Width

 N/A 4.125 in104.775 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 23.03 in585 mm

db - Cone Backface Backing Diameter

 N/A 23.39 in594 mm

Da - Cup Frontface Backing Diameter

 N/A 27.96 in710.20 mm

Db - Cup Backface Backing Diameter

 N/A 27.40 in695.96 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.3 in7.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.27 in6.9 mm
a - Effective Center Location3 N/A 0.62 in15.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 150000 lbf667000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 578000 lbf2570000 N

C0 - Static Radial Rating

 N/A 1430000 lbf6370000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 88800 lbf395000 N

Factors

K - Factor7 N/A 1.69
e - ISO Factor8 N/A 0.35
Y - ISO Factor9 N/A 1.73

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 9314.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 907.6
Cg - Geometry Factor10 N/A 0.273
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.