Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM503300

Cone Part Number

 N/A LM503349A

Cup Part Number

 N/A JLM503319

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1.8105 in45.987 mm

D - Cup Outer Diameter

 N/A 3.3465 in85.001 mm

B - Cone Width

 N/A 0.7087 in18.001 mm

C - Cup Width

 N/A 0.5512 in14 mm

T - Bearing Width

 N/A 0.7086 in17.998 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0 in0 mm
r - Cup Backface "To Clear" Radius2 N/A 0.010 in0.25 mm

da - Cone Frontface Backing Diameter

 N/A 2.01 in51 mm

db - Cone Backface Backing Diameter

 N/A 2.24 in57 mm

Da - Cup Frontface Backing Diameter

 N/A 3.03 in76.96 mm

Db - Cup Backface Backing Diameter

 N/A 2.87 in72.90 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.02 in0.5 mm
a - Effective Center Location3 N/A -0.08 in-2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3930 lbf17500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 15100 lbf67400 N

C0 - Static Radial Rating

 N/A 17000 lbf75400 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2700 lbf12000 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 28.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 22.5
Cg - Geometry Factor10 N/A 0.0789
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.