Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM603000

Cone Part Number

 N/A LM603049AS

Cup Part Number

 N/A LM603019

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1.7812 in45.242 mm

D - Cup Outer Diameter

 N/A 3.0625 in77.788 mm

B - Cone Width

 N/A 0.7812 in19.842 mm

C - Cup Width

 N/A 0.6562 in16.667 mm

T - Bearing Width

 N/A 0.8438 in21.433 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.760 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 2.05 in52 mm

db - Cone Backface Backing Diameter

 N/A 2.09 in53 mm

Da - Cup Frontface Backing Diameter

 N/A 2.94 in74.68 mm

Db - Cup Backface Backing Diameter

 N/A 2.76 in70.10 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.03 in0.8 mm
a - Effective Center Location3 N/A -0.09 in-2.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 4450 lbf19800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 17200 lbf76300 N

C0 - Static Radial Rating

 N/A 17500 lbf77900 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3250 lbf14500 N

Factors

K - Factor7 N/A 1.37
e - ISO Factor8 N/A 0.43
Y - ISO Factor9 N/A 1.41

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 26.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 14.4
Cg - Geometry Factor10 N/A 0.0785
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.