Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM665900

Cone Part Number

 N/A LM665949

Cup Part Number

 N/A LM665911

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 15.1875 in385.763 mm

D - Cup Outer Diameter

 N/A 20.2500 in514.350 mm

B - Cone Width

 N/A 3.2500 in82.550 mm

C - Cup Width

 N/A 2.5 in63.5 mm

T - Bearing Width

 N/A 3.2501 in82.553 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.530 in13.46 mm

da - Cone Frontface Backing Diameter

 N/A 15.98 in406 mm

db - Cone Backface Backing Diameter

 N/A 16.34 in415 mm

Da - Cup Frontface Backing Diameter

 N/A 19.51 in495.55 mm

Db - Cup Backface Backing Diameter

 N/A 18.58 in471.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.18 in4.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.33 in8.4 mm
a - Effective Center Location3 N/A 0.64 in16.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 78900 lbf351000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 304000 lbf1350000 N

C0 - Static Radial Rating

 N/A 710000 lbf3160000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 56500 lbf251000 N

Factors

K - Factor7 N/A 1.4
e - ISO Factor8 N/A 0.42
Y - ISO Factor9 N/A 1.43

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3743.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 480
Cg - Geometry Factor10 N/A 0.216
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.