Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM718900

Cone Part Number

 N/A LM718947

Cup Part Number

 N/A LM718910

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM718947-90010

Dimensions

d - Bore

 N/A 3.6210 in91.973 mm

D - Cup Outer Diameter

 N/A 5.625 in142.875 mm

B - Cone Width

 N/A 1.1811 in30.000 mm

C - Cup Width

 N/A 0.8661 in21.999 mm

T - Bearing Width

 N/A 1.1811 in30.000 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.94 in100 mm

db - Cone Backface Backing Diameter

 N/A 4.17 in106 mm

Da - Cup Frontface Backing Diameter

 N/A 5.46 in138.68 mm

Db - Cup Backface Backing Diameter

 N/A 5.08 in129.03 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.08 in2 mm
a - Effective Center Location3 N/A 0.07 in1.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 9540 lbf42400 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 36800 lbf164000 N

C0 - Static Radial Rating

 N/A 53900 lbf240000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 7810 lbf34700 N

Factors

K - Factor7 N/A 1.22
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.25

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 124

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 37.6
Cg - Geometry Factor10 N/A 0.136
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.