Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM72800

Cone Part Number

 N/A LM72849

Cup Part Number

 N/A LM72810

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM72849-9U2A1 LM72849-9U3A1

Dimensions

d - Bore

 N/A 0.8900 in22.606 mm

D - Cup Outer Diameter

 N/A 1.8504 in47 mm

B - Cone Width

 N/A 0.6102 in15.499 mm

C - Cup Width

 N/A 0.4724 in11.999 mm

T - Bearing Width

 N/A 0.6102 in15.499 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.04 in1.02 mm

da - Cone Frontface Backing Diameter

 N/A 1.1 in28 mm

db - Cone Backface Backing Diameter

 N/A 1.18 in30 mm

Da - Cup Frontface Backing Diameter

 N/A 1.75 in44.45 mm

Db - Cup Backface Backing Diameter

 N/A 1.59 in40.39 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A -0.12 in-3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2050 lbf9110 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 7900 lbf35100 N

C0 - Static Radial Rating

 N/A 7420 lbf33000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1660 lbf7380 N

Factors

K - Factor7 N/A 1.24
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 7.5

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 8.95
Cg - Geometry Factor10 N/A 0.0538
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.