Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM739700

Cone Part Number

 N/A LM739749WE

Cup Part Number

 N/A LM739710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM739749WE-902B7 LM739749WE-902B9

Dimensions

d - Bore

 N/A 7.7500 in196.850 mm

D - Cup Outer Diameter

 N/A 10.1250 in257.175 mm

B - Cone Width

 N/A 1.6938 in43.023 mm

C - Cup Width

 N/A 1.1875 in30.163 mm

T - Bearing Width

 N/A 1.5626 in39.690 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 8.11 in206 mm

db - Cone Backface Backing Diameter

 N/A 8.39 in213 mm

Da - Cup Frontface Backing Diameter

 N/A 9.92 in251 mm

Db - Cup Backface Backing Diameter

 N/A 9.41 in239.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A -0.01 in-0.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.12 in3 mm
a - Effective Center Location3 N/A 0.45 in11.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 18600 lbf82500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 71600 lbf318000 N

C0 - Static Radial Rating

 N/A 161000 lbf718000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 14200 lbf63100 N

Factors

K - Factor7 N/A 1.31
e - ISO Factor8 N/A 0.45
Y - ISO Factor9 N/A 1.34

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 761.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 232.3
Cg - Geometry Factor10 N/A 0.13
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.