Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM772700

Cone Part Number

 N/A LM772748

Cup Part Number

 N/A LM772710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM772748-90037

Dimensions

d - Bore

 N/A 19.2500 in488.950 mm

D - Cup Outer Diameter

 N/A 24.9950 in634.873 mm

B - Cone Width

 N/A 3.3125 in84.138 mm

C - Cup Width

 N/A 2.4375 in61.913 mm

T - Bearing Width

 N/A 3.3125 in84.138 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 20.08 in510 mm

db - Cone Backface Backing Diameter

 N/A 20.55 in522 mm

Da - Cup Frontface Backing Diameter

 N/A 24.25 in616.00 mm

Db - Cup Backface Backing Diameter

 N/A 23.62 in599.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.19 in4.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.35 in8.9 mm
a - Effective Center Location3 N/A 1.61 in40.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 108000 lbf482000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 418000 lbf1860000 N

C0 - Static Radial Rating

 N/A 871000 lbf3870000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 87800 lbf390000 N

Factors

K - Factor7 N/A 1.24
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5450

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 602
Cg - Geometry Factor10 N/A 0.253
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.