Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM806300

Cone Part Number

 N/A LM806349C

Cup Part Number

 N/A LM806310

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.1250 in53.975 mm

D - Cup Outer Diameter

 N/A 3 1/2 in88.900 mm

B - Cone Width

 N/A 0.7970 in20.244 mm

C - Cup Width

 N/A 0.5781 in14.684 mm

T - Bearing Width

 N/A 0.7968 in20.239 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.1 in2.540 mm
r - Cup Backface "To Clear" Radius2 N/A 0.08 in2.03 mm

da - Cone Frontface Backing Diameter

 N/A 2.36 in60 mm

db - Cone Backface Backing Diameter

 N/A 2.56 in65 mm

Da - Cup Frontface Backing Diameter

 N/A 3.39 in85.10 mm

Db - Cup Backface Backing Diameter

 N/A 3.15 in80.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.05 in1.3 mm
a - Effective Center Location3 N/A 0.06 in1.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 4440 lbf19700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 17100 lbf76100 N

C0 - Static Radial Rating

 N/A 22000 lbf97900 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 4150 lbf18400 N

Factors

K - Factor7 N/A 1.07
e - ISO Factor8 N/A 0.55
Y - ISO Factor9 N/A 1.1

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 35.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 22
Cg - Geometry Factor10 N/A 0.0936
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.