Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A LM869400

Cone Part Number

 N/A LM869448

Cup Part Number

 N/A LM869410

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A LM869448-90023 LM869448-90034 LM869448-902B1 LM869448-903A5 LM869448-90WA1

Dimensions

d - Bore

 N/A 17.0000 in431.800 mm

D - Cup Outer Diameter

 N/A 22.5000 in571.500 mm

B - Cone Width

 N/A 2.9375 in74.613 mm

C - Cup Width

 N/A 2.0625 in52.388 mm

T - Bearing Width

 N/A 2.9375 in74.613 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 17.83 in453 mm

db - Cone Backface Backing Diameter

 N/A 17.99 in457 mm

Da - Cup Frontface Backing Diameter

 N/A 21.66 in548.90 mm

Db - Cup Backface Backing Diameter

 N/A 21.14 in536.96 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.4 in10.2 mm
a - Effective Center Location3 N/A 1.97 in50 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 71700 lbf319000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 276000 lbf1230000 N

C0 - Static Radial Rating

 N/A 632000 lbf2810000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 67000 lbf298000 N

Factors

K - Factor7 N/A 1.07
e - ISO Factor8 N/A 0.55
Y - ISO Factor9 N/A 1.1

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3720

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 491
Cg - Geometry Factor10 N/A 0.233
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.