Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M12600

Cone Part Number

 N/A M12648

Cup Part Number

 N/A M12610

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7/8 in22.225 mm

D - Cup Outer Diameter

 N/A 1.9687 in50.005 mm

B - Cone Width

 N/A 0.7200 in18.288 mm

C - Cup Width

 N/A 0.5500 in13.970 mm

T - Bearing Width

 N/A 0.69 in17.526 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.050 in1.270 mm
r - Cup Backface "To Clear" Radius2 N/A 0.050 in1.27 mm

da - Cone Frontface Backing Diameter

 N/A 1.04 in26.5 mm

db - Cone Backface Backing Diameter

 N/A 1.12 in28.5 mm

Da - Cup Frontface Backing Diameter

 N/A 1.83 in46.48 mm

Db - Cup Backface Backing Diameter

 N/A 1.73 in43.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.01 in-0.3 mm
a - Effective Center Location3 N/A -0.25 in-6.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3040 lbf13500 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 11700 lbf52200 N

C0 - Static Radial Rating

 N/A 9780 lbf43500 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1450 lbf6440 N

Factors

K - Factor7 N/A 2.1
e - ISO Factor8 N/A 0.28
Y - ISO Factor9 N/A 2.16

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 9.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 5.63
Cg - Geometry Factor10 N/A 0.0479
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.