Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M201000

Cone Part Number

 N/A M201047

Cup Part Number

 N/A M201011

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 9/16 in39.688 mm

D - Cup Outer Diameter

 N/A 2.8750 in73.025 mm

B - Cone Width

 N/A 0.8700 in22.098 mm

C - Cup Width

 N/A 0.8400 in21.336 mm

T - Bearing Width

 N/A 1.0100 in25.654 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.760 mm
r - Cup Backface "To Clear" Radius2 N/A 0.090 in2.29 mm

da - Cone Frontface Backing Diameter

 N/A 1.89 in48 mm

db - Cone Backface Backing Diameter

 N/A 1.79 in45.5 mm

Da - Cup Frontface Backing Diameter

 N/A 2.74 in69.10 mm

Db - Cup Backface Backing Diameter

 N/A 2.52 in64.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A -0.23 in-5.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 4280 lbf19000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 16500 lbf73400 N

C0 - Static Radial Rating

 N/A 20000 lbf89100 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2440 lbf10800 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 27.5

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 15
Cg - Geometry Factor10 N/A 0.0736
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.