Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M224700

Cone Part Number

 N/A M224748

Cup Part Number

 N/A M224710

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4.7234 in119.974 mm

D - Cup Outer Diameter

 N/A 6.8750 in174.625 mm

B - Cone Width

 N/A 1.4375 in36.513 mm

C - Cup Width

 N/A 1.0938 in27.783 mm

T - Bearing Width

 N/A 1.4063 in35.720 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 5.08 in129 mm

db - Cone Backface Backing Diameter

 N/A 5.28 in134 mm

Da - Cup Frontface Backing Diameter

 N/A 6.65 in167.90 mm

Db - Cup Backface Backing Diameter

 N/A 6.38 in162.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.04 in1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.14 in3.6 mm
a - Effective Center Location3 N/A -0.14 in-3.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 14200 lbf63400 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 54900 lbf244000 N

C0 - Static Radial Rating

 N/A 94900 lbf422000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8110 lbf36100 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 279.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 86.6
Cg - Geometry Factor10 N/A 0.158
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.