Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M236800

Cone Part Number

 N/A M236848

Cup Part Number

 N/A M236810

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7 in177.800 mm

D - Cup Outer Diameter

 N/A 10-1/4 in260.350 mm

B - Cone Width

 N/A 2.125 in53.975 mm

C - Cup Width

 N/A 1.6250 in41.275 mm

T - Bearing Width

 N/A 2.1250 in53.975 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.870 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 7.52 in191 mm

db - Cone Backface Backing Diameter

 N/A 8.03 in204 mm

Da - Cup Frontface Backing Diameter

 N/A 9.82 in249.40 mm

Db - Cup Backface Backing Diameter

 N/A 9.49 in241.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.15 in3.8 mm
a - Effective Center Location3 N/A -0.26 in-6.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 31300 lbf139000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 121000 lbf537000 N

C0 - Static Radial Rating

 N/A 210000 lbf933000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 17800 lbf79200 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 690.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 100.2
Cg - Geometry Factor10 N/A 0.115
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.