Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M238800

Cone Part Number

 N/A M238849

Cup Part Number

 N/A M238810

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7.3750 in187.325 mm

D - Cup Outer Diameter

 N/A 10.6250 in269.875 mm

B - Cone Width

 N/A 2.1875 in55.563 mm

C - Cup Width

 N/A 1.6875 in42.863 mm

T - Bearing Width

 N/A 2.1875 in55.563 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 7.91 in201 mm

db - Cone Backface Backing Diameter

 N/A 8.07 in205 mm

Da - Cup Frontface Backing Diameter

 N/A 10.16 in258.06 mm

Db - Cup Backface Backing Diameter

 N/A 9.84 in249.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.21 in5.3 mm
a - Effective Center Location3 N/A -0.24 in-6.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 32000 lbf142000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 123000 lbf548000 N

C0 - Static Radial Rating

 N/A 225000 lbf999000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 18200 lbf80900 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 788

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 118
Cg - Geometry Factor10 N/A 0.120
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.