Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M268700

Cone Part Number

 N/A M268742

Cup Part Number

 N/A M268710

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 16.5350 in419.989 mm

D - Cup Outer Diameter

 N/A 23.2500 in590.550 mm

B - Cone Width

 N/A 4.5000 in114.300 mm

C - Cup Width

 N/A 3.5000 in88.900 mm

T - Bearing Width

 N/A 4.5000 in114.300 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 17.48 in444 mm

db - Cone Backface Backing Diameter

 N/A 17.48 in444 mm

Da - Cup Frontface Backing Diameter

 N/A 22.16 in562.86 mm

Db - Cup Backface Backing Diameter

 N/A 21.61 in548.89 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.33 in8.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.34 in8.6 mm
a - Effective Center Location3 N/A -0.37 in-9.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 166000 lbf740000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 642000 lbf2860000 N

C0 - Static Radial Rating

 N/A 1250000 lbf5550000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 94800 lbf421000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5754.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 420.9
Cg - Geometry Factor10 N/A 0.232
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.