Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M278700

Cone Part Number

 N/A M278749

Cup Part Number

 N/A M278710

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A M278749-902A1

Dimensions

d - Bore

 N/A 22.5000 in571.500 mm

D - Cup Outer Diameter

 N/A 32.0000 in812.800 mm

B - Cone Width

 N/A 6.1250 in155.575 mm

C - Cup Width

 N/A 4.7500 in120.650 mm

T - Bearing Width

 N/A 6.1250 in155.575 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 23.98 in609 mm

db - Cone Backface Backing Diameter

 N/A 24.21 in615 mm

Da - Cup Frontface Backing Diameter

 N/A 30.47 in773.70 mm

Db - Cup Backface Backing Diameter

 N/A 29.76 in755.90 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.34 in8.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.53 in13.5 mm
a - Effective Center Location3 N/A -0.45 in-11.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 264000 lbf1180000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1020000 lbf4530000 N

C0 - Static Radial Rating

 N/A 2370000 lbf10600000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 150000 lbf669000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 12425.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 669.4
Cg - Geometry Factor10 N/A 0.299
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.